“Power Maxx Deadlift Mini Jack” has been added to your cart. View cart

Close-up of a metallic barbell labeled ATX® Olympic Power Barbell - Black featuring two skulls and red accents, with a marked weight of 20 kg and a circular detail highlighting the bars end cap design.

Close-up of a barbell end cap marked Death Bar and ATX with stylized skulls featuring red eyes, 20 KG, and a metallic finish on the ATX® Olympic Power Barbell - Black.

Close-up of the ATX® Olympic Power Barbell - Black featuring a smooth silver sleeve and black textured grip on the bar. A golden ring marks where the bar connects, enhancing its design.

ATX® Olympic Power Barbell – Black

Write a Review

$539.00

Item No: ATX-LH-50-LDBC

5 in stock

DESCRIPTION

Weight Weight The base weight of the item, without any packaging.	21 kg
Dimensions	223 × 8 × 8 cm
Grip Diameter	28.5mm
Sleeve Rotation	Bushing
Length	220cm
Sleeve Length	42cm
Coating	Chrome/Oxide
Load Capacity	700kg
Weight Weight The base weight of the item, without any packaging.	20kg+/-0.2%
Knurl Marking	IPF/IWF
Centre Knurl	None
Knurling Aggression	Medium
Tensile Strength	206K

ATX® Olympic Power Death Bar

The ATX® Power Bar- Black is the latest addition to our ATX® barbell range. If you are after a bar that stands out from the pack, not just visually but performance too, then the Power Barbell is just for you.

Material – special steel according to EN 102775-5
Barbell Shaft – 28.5 mm.
Sleeves – Non-slip ribbing, combined with chrome finish.
Bushings – self lubricating bronze bushings.
Weight load capacity – 700kg.
Knurling – Medium deep with powerlifting and weightlifting markings.
No centre knurl.

Image of the ATX® Olympic Power Barbell - Black with 2200 mm total length, 1310 mm shaft, 910 mm inside collar, and 420 mm sleeve. It has a 28.5 mm diameter, weighs 20 kg, features copper bushings and knurling, boasts a tensile strength of 206K PSI, and includes a 5-year warranty.

Dual Knurl Marking

The ATX® Power Death Bar is very similar to the ATX® Black Mamba Power Bar, the only difference would be chrome sleeves.

The Death Bar is made out of very strong and elastic spring steel. It has a massive 206,000 PSI (Tested!) meaning you will need quite a few plates to break it. Barbells under 190,000 PSI tend to bend over time from continuous use, while barbells over 190,000 PSI will remain straight even after years of lifting.

This bar offers dual markings (powerlifting and weightlifting) and no central knurling. Bars with no central knurling won’t scrape your chest when performing Olympic lifts.

Weight Load Capacity

The weight load capacity varies between exercises due to the relevant load support of the different exercises. Squats are the lowest at 500kg because the load is only supported in the centre of the bar by your shoulders. Conversely, when you bench press your hands are spaced wider than the other lifts. This means there is less strain on the bar.

Regardless these capacities will not be an issue. The person that squats more than 500kgs will no doubt have back wider than the average bench press grip.

Please refer to the table below:

Grip Type	Maximum Permitted Weight	Example of Exercise
Wide Handle Width	700 kg	Bench Press
Medium Handle Width	600 kg	Deadlift
Central/Narrow Handle Width	500 kg	Squats

ATX® offers top-quality, tested equipment for professional use.

The ATX® weight bars are tested in a German independent testing laboratory with the following material tests:

Tensile test acc. To DIN EN ISO 6892-1.
Hardness Rockwell acc. to DIN EN ISO 6508-1

The barbell has the following values: tensile strength (Tensile Strength): 206,000 psi = 206 K (K / NSI = kilo pounds per square inch) = / corresponds to 1420 N / mm2 HRC / surface hardness: 44.0

What’s Included? ATX® Olympic Power Death Bar (ATX-LH-50-LDBC)

Please note the pictures may feature optional attachments or items which are not included with the unit, this is to show the possible configurations/use of the unit.